Home
About MMI
Products
Product Categories
Holiday Special
New Products
Commission Package
Replacement Parts
Boat Maintenance
Clearance
Shopping Cart
 
My Account
Customer Care
Manufacturers
Consulting Center
Categories » All » Marine Paint & Supplies » Marine Varnish » Bristol Finish Classic Clear..
Bristol Finish Classic Clear Water Based Interior Urethane, Soft Satin Quart
ITEM# : BRIB-8010
Product Name : Bristol Finish Classic Clear Water Based Interior Urethane, Soft Satin Quart
Category : Marine Paint & Supplies » Marine Varnish
Weight : 4 lbs
Now Only : $44.92 USD / EACH
Quantity :
0 EACH in your cart.
In Stock (5)
In stock available for immediate shipment until run out stock

Product Application Interior

Bristol Finish Classic Clear Water Based Urethane requires the same basic prep as ordinary coatings, but the application is both easier and faster. Save almost 75% of the labor compared with ordinary coating products!

Preparation Procedures

New or Bare Wood: Sand as required up to 220 grit. Remove dust and wipe with acetone. Wipe with a tack rag. Apply 1 or 2 coats of any commercial sanding sealer, following manufacturer�s instructions. Sand as required to level raised grain. Remove dust and wipe with a tack rag.

Previously Finished Surfaces: New coatings should be allowed to cure fully before over-coating with Classic Clear Water Based Urethane. Check compatibility on a small area before coating large areas.

Sand with 220 grit until smooth and dull. Use a red ScotchBrite pad for sharp corners and edges. Remove dust with a clean damp towel, then lightly wipe with a tack rag.

 

Application Procedures

Stir thoroughly before using. Use bristle or foam brushes, rollers or spray equipment. Use a floor coating applicator for large flooring areas. Apply a thin even coat with the grain of the wood. Allow to dry for a minimum of 1 hour. Apply a second coat when the first coat is not tacky. If grain raising has occurred or first coat has dried longer than 4 hours, sand with 220 grit. Remove dust with a clean damp towel, then wipe with a tack rag, and apply the second coat. More coats may be applied if desired.
Clean equipment thoroughly with water. Clean up spills immediately

 

Compatibility
Apply over wood stains, sealers, and existing finishes if in good condition. Oil finishes or wax must be removed.

Application Methods
Suitable for brush, roller or spray

Recoat Time
1 to 4 hours at 70�F (21�C)
 


 

Related Product (1/1)
Only $13.21 US
Only $8.11 US

MMI Marine is your best source when you need replacement parts for Taiwan boats and other yacht replacement parts. Our vast selection of discount marine parts and accessories will help you rest assured that you are getting the finest quality parts at the best available pricing.

Our inventory includes more than 200,000 items, such as hardware, equipment, electrical components, safety gear, appliances, lighting, and more. We work with top brand manufacturers to make sure you are choosing from the very best in replacement parts for Taiwan boats, and shipments can be made from either our domestic division or our Taiwan-based operations.

Your yacht is your symbol of success and we understand that you only want the best when it comes to updating your systems or completing basic repairs. You can turn to us for everything from detailing chemicals to pumps, and even complete commission packages. Let us be your trusted one stop source for all the yacht replacement parts you need.

M.M.I.
894 W. 16th St.
NEWPORT BEACH, CA.92663, USA
TOLL FREE: 1-800-7473014
TEL: (949)631-0518
FAX: (949)631-0313
Email: info@mmimarine.com
Product offering and prices listed on this website (www.mmimarine.com) are limited to Internet orders and prices subject to change without notice.
We accept paypal, credit cards & wire transfer.
Acceptance Mark
| NEWS | CONTACT US | PRODUCTS | WARRANTY | PRIVACY POLICY |
© 2006-2024 MAGNA MARINE INC(DBA M.M.I.) All Rights Reserved